Emergency response for burst supply lines — frozen splits, corrosion blowouts, and joint failures. We isolate the water, cut out the failed section, and splice in a tested repair, then help you stage the cleanup. Rapid dispatch.
Burst Pipe Repair is one part of our plumbing repair coverage in Michigan. For the full picture — symptoms, costs, and when to repair vs. replace — start with the complete Plumbing Repair guide, or browse every plumbing repair service we offer.
A burst pipe is one of the fastest sources of major home damage — a failed supply line pushes several gallons a minute into floors, walls, and the space below until someone closes the main. Burst pipe repair is an emergency service: we dispatch fast, and the first move on arrival is always to stop the water, either at the main or by isolating the failed branch. Once the flooding stops, we find the burst, cut back to sound pipe, and splice in a tested repair so the home is watertight again the same visit.
Most bursts trace to one of three causes, and each changes the repair. A freeze burst splits the pipe wall along its length or blows a soldered joint apart, usually on an exterior wall or an unheated Michigan crawlspace — we replace the split section and insulate or reroute so it doesn't refreeze. A corrosion blowout on old galvanized or pitted copper means the pipe is thin everywhere, so we flag the run beyond the repair. A joint or fitting that let go under pressure gets remade correctly rather than re-tightened.
Speed matters, but so does not leaving you with a hidden second problem. After the repair we pressure-test the line, then help you stage the water cleanup — pulling wet insulation, opening a cavity to dry, and pointing out where a moisture problem will grow if it isn't addressed. If the burst flooded a finished ceiling or wall across Michigan, we document it for your insurance claim and can coordinate the drywall repair, so the emergency ends with a real fix rather than a patch over a wet wall.
Different job? Start on the right page:
Pipe Repair — if the leak is slow or contained, not an active burst.
Symptoms that call for burst pipe repair
Water spraying or pouring from a pipe
An open burst floods a space by the minute. Shut your main valve if you can reach it and call — the sooner the water stops, the less floor, wall, and ceiling it destroys in a Michigan home.
A dramatic drop in pressure across the house can mean a supply line has burst and is dumping water before it reaches the fixtures. It's a cue to find the main shut-off fast.
Water stains or bulging walls and ceilings
A ceiling that sags or a wall that bulges after a cold snap is holding water from a burst line above. Opening it to repair and dry prevents a collapse across Michigan.
No water from the taps in winter
Taps that run dry during a freeze mean a pipe is frozen — and a frozen pipe is a burst waiting to thaw. Calling before it thaws lets us find and address the split proactively.
Banging pipes then a leak
A hard water-hammer bang followed by a leak is a joint or fitting that failed under a pressure spike. The burst point is usually the connection that banged loudest in the Michigan system.
What's behind it — and how we fix it
Frozen pipes
Water expands about 9% as it freezes, and the pressure between the ice plug and a closed tap splits the pipe or blows a joint. Uninsulated Michigan exterior walls, crawlspaces, and attics are where it happens.
Corrosion and age
Old galvanized steel and pitted copper thin from the inside until the wall can no longer hold pressure and blows out. A corrosion burst usually means the whole run is near failure, not just the hole.
Excessive water pressure
A failed PRV or municipal over-pressure pushes the system past what the weakest fitting can hold until it bursts. Fixing the pressure alongside the pipe stops the next Michigan blowout.
Water hammer and pressure spikes
Fast-closing valves and appliance solenoids send shock waves that fatigue joints until one fails. Repeated hammering is the warning before the burst around Michigan.
Failed fittings and old solder joints
A cold solder joint or a stressed compression fitting lets go years later, often under normal pressure. We remake the joint properly rather than reseal a failure point.
From call to fix — our process
1
Call or schedule online. Pick a 2-hour window for burst pipe repair in Michigan, by phone or online. Within five minutes you get a confirmation carrying the assigned tech's name and photo.
2
On-site diagnosis. Diagnosis happens on-site: free for most burst pipe repair repairs, $39 on minor service calls (waived if you proceed). Nothing starts until you've seen the issue and the plan.
3
Flat-rate quote. You get a flat-rate burst pipe repair quote in writing, good for 30 days — no hourly creep and no add-ons after the fact.
4
Done the same visit. Most burst pipe repair work finishes the same visit: our trucks carry the common valves, fittings, cartridges, and fixtures, so a second trip is rare.
Burst pipe repair cost in Michigan: what to expect
Burst Pipe Repair in Michigan starts at from $199, every burst pipe repair quote is flat-rate and presented in writing before work begins — no surprise add-ons, no hourly creep. Seniors (65+) and military save 10% on labor, and financing covers projects over $1,500 at 0% APR for 12 months, with no prepayment penalty.
What makes our burst pipe repair different in Michigan
We've been a trusted choice since 1974 — over 50 years of family-owned plumbing service across Michigan. Our techs are CSLB-licensed (#1098234), background-checked, and complete an internal 12-week training program before rolling on calls alone.
Our burst pipe repair carries a 10-year workmanship guarantee — separate from any manufacturer warranty on the parts themselves. If the burst pipe repair we performed fails because of how we did it, we come back and fix it free for a full decade. Appliances and fixtures we install are backed by their full manufacturer warranty, and the parts and accessories we fit carry standard 1–5 year warranties by item.
We quote burst pipe repair on honest scope: no unnecessary up-sell, salaried (never commissioned) technicians, and a transparent diagnostic so you see exactly what we see — including the parts still in good shape. If a repair is the right call we say so; if replacement is the better long-term economics, we say that. The flat-rate burst pipe repair quote is written and good for 30 days.
Burst pipe repair coverage, city by city
We provide burst pipe repair throughout Michigan, with fast coverage in every major Michigan metro.
Reach times for burst pipe repair vary by traffic and time of day, so we quote an accurate ETA when you call — and the dispatch line routes straight to an on-call technician, no voicemail in between.
Your burst pipe repair questions, answered
Top questions homeowners searching for Burst Pipe Repair near me ask us:
What do I do the moment a pipe bursts?
Shut off your main water valve — usually where the line enters the home or at the street meter — to stop the flooding, then call us. Kill power to any area taking on water. We'll coach you through the shut-off on the phone while our Michigan truck rolls.
Can you repair it in one visit?
In the large majority of cases, yes — the truck carries pipe, fittings, and push-connect couplings for a fast, tested repair. If the burst revealed a whole run of failing pipe, we make the home watertight now and schedule the section or repipe next across Michigan.
Will you help with the water damage?
Yes — after the repair we help stage the cleanup, pull wet material to dry, and document the damage for your insurance claim. We can coordinate the drywall and ceiling repair too, serving ZIPs and the surrounding Michigan area.
Why did my pipe burst?
Most often a freeze split, a corrosion blowout on old pipe, or a joint that failed under a pressure spike. We identify the cause during the repair and address it — insulation for freeze, a PRV for over-pressure — so the same pipe doesn't burst again in Michigan.
How fast can you get to a burst pipe?
Burst pipes are top-priority emergency dispatch, and our average on-site time is well under 90 minutes in covered areas. The dispatcher stays on the line to walk you through stopping the water across Michigan while we're en route.